Page 564 - Cornwell Product Catalog

TUBING & EXHAUST
HR165
Master In-Line Flaring Kit
Unique design locks the adapters, cone and tube in line making perfect factory flares every time with less risk of breaking adapters. With
the clamp and set screws putting pressure directly over the tube,
it greatly reduces the chance of the tube slipping from the clamp, and increases the overall life
of the clamp by not wearing down the teeth inside from repeated slipping. Slender low profile design permits the making of flares on the vehicle and in tight spaces. Flares can be achieved along frame rails or areas in the engine compartment, saving time from having to remove components or complete lines to make repairs. Set includes everything needed to do the following: 3/16”, 1/4”, 5/16”, 3/8” double and single flares, and 4.75mm, 6mm, 8mm double, bubble and single flares.
MCL71100
Bubble Flaring Tool Kit
Fashions I.S.O. (International Standards Organization) bubble flare found on European, Japanese and some domestic model brake lines. Flares without removing brake lines from a vehicle. Includes: hardened steel bar, adapters for 4.75, 6, 8 and 10mm O.D. tubing, and carrying case
HR157
Constant Tension Mini Tube Cutter
Can cut tube sizes ranging from
3/16" to 7/8".The constant pressure
tube cutter utilizes a spring to keep
consistent compression on the cutting
blade to the tube.To use turn adjustment handle until the alignment marks line up, then turn the cutter to until the tubing is cut.
HR158
Constant Pressure Tube Cutter
Utilizes a spring to keep consistent
compression on the cutting blade
to the tube. This allows the user
to cut through thin walled steel
tubing without having to continually
tighten or adjust the cutter. Simply turn the adjustment handle until the alignment marks line up, then turn the cutter until the tubing is cut. Makes the task of cutting through steel walled tubing faster and easier.
HR159
Mini Constant Pressure Tube Cutter
Utilizes a spring to keep consistent
compression on the cutting blade to the tube.
This allows the user to cut through thin walled
steel tubing without having to continually
tighten or just the cutter. Simply turn the
adjustment handle until the alignment marks
line up, then turn the cutter until the tubing is cut. Makes the task of cutting through steel walled tubing faster and easier.
MCL70027
Mini Tube Cutter
Carbide steel cutting wheels work with hard
and soft copper, aluminum, brass, thin wall
steel and stainless steel. Rollers with flare
cut-off grooves to salvage as much old tubing
material as possible. For 1/8” to 5/8” O.D. Tubing (1/8 - 1/2” Nominal).
RA42071
Ratcheting Tubing Cutter
Designed for confined spaces. Unique
ratcheting action operates like a
socket ratchet but cuts copper,
aluminum, stainless steel, and PVC.
Spring-loaded adjusting screw applies
continuous pressure while cutting. For cutting 1/8” to 1/2” tubing.
TC470FH
Tubing Bender
Triple head 180° tube bender with Roto-LokTM indexing handle. Bends 3/16”, 1/4”, 5/16” and 3/8” O.D. tubing. Patented, quick-action indexing lever repositions two-stage handle midway through bend when both handles begin to meet. This feature allows easy fabrication of bends
up to 180° with reduced effort, better control and no crossing of handles. Optimum bending radius for each tubing size. Calibrated markings for making accurate left-hand, right-hand and offset bends. Compact design for working in tight spaces. Cushion grips for comfort and stability. Made of lightweight, die-cast aluminum.
LS44150
3/16” Tubing Bender Pliers
Bends brake lines without
kinking or flattening, especially
in tight spots. Bends all types
of 3/16” and 1/4” O.D. tubing. Unique head design bends tubing without collapsing the tube. Won’t mark tube surface. The handles are more than 3-1/4” apart for proper leverage when handling even steel tubing.
562 1-800-321-8356
UNDERCARRIAGE & WHEEL