Page 540 - Cornwell Product Catalog

PULLERS/SEPARATORS
OW1123
Bearing Splitter - 1/2” to 4-5/8”
Features “knife-like” edges which are easily placed behind the part
to secure a gripping surface, even when clearances are extremely limited. Max. Spread: 4-5/8”. Min. Spread: 1/2”. Thread of tapped
holes in adapter: 5/8”-18. Distance between adjusting screws: 4-3/8”. Use with puller numbers: OW1035, OW1036, OW1037, OW1038, and OW927.
OW1130
Bearing Splitter 1/2” - 9”
Features “knife-like” edges which
are easily placed behind the part
to secure a gripping surface, even
when clearances are extremely
limited. When used with a “Grip-
O-Matic®” puller, puller jaws grip
attachment’s outer edge; when used
with a Push-Puller, puller legs are
threaded into the attachment’s two tapped holes. Maximum spread: 9”. Minimum spread: 1/2”. Thread of tapped holes in adapter: 5/8”-18. Distance between adjusting screws: 6”. Use with puller numbers: OW1035, OW1040, OW1041, OW1042, OW1065, OW1063 and OW938.
OW4581
Blind Hole Bearing
Puller Set
For pulling jobs requiring an
internal pull, such as pilot
bearings. Set includes four
collets which fit a wide range
of applications. Select the
appropriate sized collet by comparing it with the application. Insert the collet, expand it to fit the hole, then attach the slide hammer assembly. Four collet sizes: 3/8" to 1/2", 9/16" to 11/16", 5/8" to 1", 1" to 1-1/4". Set includes a 2-1/2 pound slide hammer with T-handle. Housed in a blow-molded plastic storage case. Weight: 7 lbs., 2 oz.
HR29
Blind Hole Bearing Puller Set
Designed for removing
recessed bearings. Set
includes a 2-1/2" lb. slide
hammer with T-Handle
and four collets, for a wide
range of applications. Ideal
for removing pilot bearings. Collet sizes: 3/8" to 1/2" (10mm - 14mm), 9/16" to 11/16" (15mm - 19mm), 5/8" to 1" (18mm - 25mm), and 1" to 1-1/4" (25mm - 32mm)
HRC4579
9 Way Puller Set
Pulls flange-type rear axles and most front wheel drive hubs. Internal and external jaws provide a variety of combinations to pull bearings, gears and seals. Two and three-way cross blocks and cone provide the perfect jaw configuration for most jobs. Includes a grip wrench adapter and a dent puller attachment for sheet metal or other unique pulling requirements.
Includes:
PART #
OW45811 OW45812 OW45813 OW45814 OW45815
DESCRIPTION
1/2” Collet and Pin Assembly 3/4” Collet and Pin Assembly 1” Collet and Pin Assembly 1-1/4” Collet and Pin Assembly Slide Hammer Assembly
Includes:
PART #
HR49801 HR526100 HR526200 HR526300 HR9561 HR956100 HR9562 HR956200 HR9563 HR956300 HR9564 HR956400 HR9565 HR956500 HR956600
DESCRIPTION
Rear Axle Puller Flange Front Axle Puller (tall) Center Screw
Nut, FA Puller
Jaw Spreader Cone T-Bar
Cross Bar 2 Jaw Dent Puller Screw 3-way Puller Yoke
5 lb. Hammer Hook Adapter
Jaw (3 pc. set) Screw and Bolt Set Grip Wrench Adapter Nose Cone
538 1-800-321-8356
UNDERCARRIAGE & WHEEL