Page 482 - Cornwell Product Catalog

ENGINE TOOLS
// Harmonic Balancer Tools
HR38800 Harmonic Balancer Installer
Designed to properly install harmonic balancers or drive pulleys that are pressed on the crankshaft. Instructions included. Packaged in blow- molded case.
Includes:
PART #
HR388400 HR388500 HR388600 HR388700 HR388800 HR388110 HR388120 HR388160 HR388170 HR388180 HR388300 HR388900
HR189
Harmonic Balancer
Puller
HRC38000
Ratcheting Harmonic
Balancer Pulley Puller
Ratcheting, quick-release jaws with push-turn design for fast 2-jaw and 3-jaw configuration. Unique offset legs grab pulley spokes. Low profile eliminates the need to remove radiator. Indexing legs hold position while working. Compatible with 3, 4 and 6 spoke pulleys, including Ford Coyote 5.0 L; GM 5.3L, 5.7LS1, 6.0LS2, 6.2LS3, and 7.0L.
SIZE
1/2”-20 3/4”-16 5/8”-18 7/16”-20 9/16”-18 M14mm 1.5 (black) M16mm 2.0 (black) M10mm 1.5 (black) M14mm 2.0 (black) M16mm 1.5 (black) M12mm 1.75 (black) M12mm 1.5 (black)
Includes:
PART #
HRC38001 HR38002 HR38003 HR38004
HRC6667
DESCRIPTION
Ratcheting Yoke Forcing Screw
Offset Harmonic Jaw
Flat Press Adapter with O’Ring
Designed to pull balancers,
vibration dampers, pulleys
and gears with tapped holes.
The four (4) slots in the yoke
allow tool to be used for
either two (2) or three (3)
hole applications. The removable floating swivel prevents damage to shaft ends. Comes complete the necessary side screws and center screw. Zinc plated. Yoke is forged from alloy steel, heat treated.
GM/Chrysler Harmonic Balancer Puller
Designed for removing
damper pulleys in tight
engine compartments,
without removing the
radiator. Kit contains the
3-jaw puller, four lengths of
forcing rods, and a forcing
screw with a 3/8” square
drive for ratchet use, and a
3/4” hex for wrench or socket
use. APPLICATIONS: GM
2000 Generation III 4.8L, 5.3L, 5.7L, 6.0L and 8.1L V8s; Cadillac 4.5, 4.6, and 4.9L V8s beginning in 1988; Chevrolet trucks 2003-later 4.2L I6, 2004-current 3.5L I5 and 2005-current 2.8L I4 ; Chrysler engines from 1990-later, including 2.0L, 2.4L-4s; plus 2.5L, 2.7L, 3.3L, 3.5L, and 3.8L V6s; Ford 1995-later V8 engines with 3 spoke pressed on damper; and Mitsubishi Eclipse 1995-1999 2.0L DOHC non-turbo.
HRC38110
Ford Harmonic Balancer Holder
Works on most 1992-2016 2.5L and 3.0L V6 Duratec engines, including F-Series, Contour, Taurus, Jaguar, Lincoln, Mercury, and Mazda. Hold harmonic balancer
in place while loosening / tightening retaining bolt. Use with 1/2" ratchet or breaker bar. Holes allow bolt installation
to hold puller in place. Eliminates the
need to lock engine at the flywheel. Prevents damage to the harmonic balancer.
Includes:
QTY. PART #
1 HR1891
1 HR1892
1 HR189300
3 HR189500
3 HR189600
2 HR189700
3 HR189800
DESCRIPTION
Yoke Only Replacement Screw Swivel & O-Ring 3/8”-24 x 2” Side Screw 5/16”-18 x 2” Side Screw 3/8”-16 x 4” Side Screw M8 x 1.25 x 80mm Side Screw
480 1-800-321-8356
UNDERHOOD