Page 18 - November 2020 Promotional Flyer
P. 18

UNDERHOOD
Tester
Diesel Compression Test Kit
Master Harmonic Balancer Puller Kit
$139.95 $169.95
Steel reinforced hose
and 2-1/2” gauge
with rubber protector
that reads 0-1000
PSI. Side release
valve and swivel end
quick coupler. Works on many VW, Volvo, Audi, GM, Isuzu, Toyota, Mercedes, BMW and Nissan engines.
Master Compression Tester
$159.95 $179.95 HM30ACW
Deluxe compression test kit for domestic and foreign cars and trucks. 2-1/2” dual scale gauge range from 0 to 300 PSI and
0 to 21 bar. M14 short, M14 long & M12/M16 combo hose adapter. M10 solid adapter. Small engine gauge and
hose assembly. Solid adapter
extension for deep seated plug applications.
Transmission and Oil Pressure Tester $129.95 $149.95 GSI3150
Checks oil pressure in both automatic transmissions and engines. High pressure gauge reads 0-400 in PSI and metric, and low pressure gauge is 0-100 in PSI and metric readings. Includes 9 feet of hose with both US and metric fittings. Comes with wire hang-up assembly.
Large Valve Spring Compressor
$69.95 $79.95 CTGLVSC
Easily compress valve
springs on overhead
valve engines with
the cylinder removed.
Specially designed
valve spring adapters
allow visibility and access to valve spring retainers. Direct-action compressor lever provides superior strength and control. Two valve spring adapters that fit retainers up to 1" (25mm) and 1-3/16" (30mm).
Serpentine Belt Tool
$224.95 $305.75
GSI2000
LS54810
  Dual Gauge Cylinder Leakage
$99.95 $117.95 HMCLT2CW
Pin-points problem shown by compression
test or cylinder balance test. Uses shop air to determine leakage source and the amount of leakage measured in percentage of loss. The pressure gauge monitors inlet pressure to ensure accurate testing. Leak down gauge measures the percentage of compression leakage.
19mm Detroit Diesel Injector Line
$44.95 $49.95
Removes most
automotive
harmonic
balancers.
Includes: standard
harmonic balancer
puller, pulling
screws, adapters (for 3300 and 3800 GM V6 engines), harmonic damper pulley puller (for Chrysler, GM, Mitsubishi, & Dodge) and interchangeable puller jaws (for 3.6L V6 Chevrolet Camaro and Dodge 5.7L Hemi)
2-Jaw Harmonic Pulley Puller with Side-Turn Legs
$129.95 $149.95 SLC17400
Specially designed for 4-spoke
pulleys. Patent-pending,
side-turn legs easily grab and
center on the pulley. Narrow
design fits the small pockets
found on most pulleys.
Spring-loaded legs maintain
position and save time as the
puller is positioned on the pulley. Compact size fits in tight engine spaces. Applications include GM Geo, Chevrolet Spark, Nissan, Infinity, Mitsubishi, Toyota, Lexus and Scion vehicles.
2-Jaw Harmonic Pulley Puller with Side-Turn Legs
   Socket
ARDDF19
 Removes and installs high-pressure
injector lines on Detroit Diesel DD13,
DD15 and DD16 engines. Offset
design and 3/8" drive allows access
to cylinder #6. 60mm length. Comparable to J-48770.
Master Disconnect Set
$179.95 $199.95
SLC18350
 $59.95 $75.85
Includes: 8 popular disconnect tools for
A/C and fuel lines.
A complete set of disconnect tools that can be stored in a handy blow-molded case.
Specially designed for
3-spoke pulleys. Patent-
pending, side-turn legs
easily grab the backside
of the pulley spokes.
Narrow design fits the
small pockets found on
most pulleys. Spring-
loaded legs maintain
position. Compact size fits in tight engine spaces. Applications include GM Chevrolet Camaro 3.6L, 2018 Ford Mustang Coyote, 3.0L Duratech and more.
Tru-Grip Serpentine Belt Install Tool
$26.95 $31.95 HR734
Clamping jaw allows user to position serpentine belt without the belt slipping out of the tool. Tru-grip and long reach allows belt routing in tight access areas that would normally be difficult if not impossible. Body made of lightweight alloy steel for durability and strength. Ergonomic handle provides comfort and ease in use, acting as an extension of the user’s hand.
LS39900
  7 Piece Sensor
  Socket Set
$59.95 HRC4673
A comprehensive
socket set that enables
technicians to easily install
or remove oxygen sensors,
vacuum switches and oil
pressure sending units on
a wide variety of domestic
vehicles and imports. This versatile set includes SAE and metric sockets for the most common applications.
$64.99 $91.95
HRC4645
 18 WWW.CORNWELLTOOLS.COM
NOTE: All items shown in this flyer are limited in quantities and subject to availability. Please also note that the printed color may differ from the actual color due to variations in the printing process. Cornwell®, the Ironman Logo, The Choice of Professionals® and bluePOWER® are registered trademarks of the Cornwell® Quality Tools Company.
Fits
tensioner
pulleys with
13mm to
16mm, 18mm hex or 3/8” and 1/2” square drives. There are 13mm and 15mm 12 point wrenches built into the handle for hard to access tensioners. 13mm, 14mm and 15mm crowfoot wrenches also included.
  
   16   17   18   19   20